Jasco Z-Wave Plus Motion Sensor On/Off Wall Switch (Gen5)
DEALER ONLY ITEM: Not Available Directly to End Users.
Dealers, log on to see pricing. »Sign up to become an authorized installer.
Z-Wave On/Off Switch with Vacancy/Occupancy Sensing
Save energy while enjoying Z-Wave control over your wired light fixture by replacing your traditional switch with the Jasco Z-Wave Plus Motion Sensor On/Off Wall Switch (Gen5). This Z-Wave light switch has a built-in PIR motion sensor to serve as a vacancy or occupancy sensor, automatically turning the light off when the room is empty. You can also manually turn the light on/off through your Z-Wave controller or using the local button switch. A blue LED indicator helps guide you to the switch through the dark.
- Works with incandescent, LED, xenon, halogen and fluorescent lighting
- Sensor can be set to occupancy, vacancy, or manual mode
- Suitable for single-pole or multi-pole applications
- Can be included in multiple groups or scenes
- "Z-Wave Plus" certified for wide compatibility
- Uses a standard decorative-size wallplate (sold separately)
Available Colors: White paddle installed. Light Almond paddle included.
The switch's motion sensor can be set to occupancy mode, vacancy mode, or manual mode. In vacancy mode, a person has to manually turn the light on, but the light will turn off after the room has become vacant (no motion detected). In occupancy mode, the light automatically turns on when a person enters the room and also optionally only if the room is dark, and then automatically turns off when the room becomes vacant. In manual mode, the motion sensor does not come into play and lights must be turned on/off manually, either at the button switch or via Z-Wave.
Z-Wave Plus Certification
Z-Wave Plus is an upgraded certification program to help you identify products that take advantage of the "Next Gen" Z-Wave hardware platform, also known as 500 Series or Gen5 Z-Wave. Z-Wave Plus certified solutions feature a selected set of extended features and capabilities that enhance your experience with faster and easier installation and setup. Z-Wave Plus advancements also provide longer battery life, faster operation, better wireless range and improved noise immunity.
The Z-Wave Plus Motion Sensor On/Off Wall Switch works with incandescent lighting up to 960 Watts, or a load up to 1/2 HP or 1800W/15A resistive. The switch supports single-pole or multi-pole applications, and works in conjunction with up to three aux/remote switches (requires the toggle or rocker-style Jasco Z-Wave Auxiliary Switch, sold separately). This model can also be included in multiple zones/scenes.
- Works with incandescents up to 960W
- Supports loads up to 1/2 HP or 1800W/15A resistive
The switch requires standard screw terminal installation with wiring connections for Line (Hot), Load, Neutral, and Ground. Multi-pole installation also requires a traveler wire.
NOTE: Requires a Z-Wave network controller. Wallplate not included. Uses standard single-gang wallplate. For indoor use only.
Z-Wave Compatible Automation Hubs
Jasco: Leader And Innovator In Electronics
Established in 1975, Jasco Products is a leader in the design and development of home automation products and wireless accessories. Jasco develops consumer electronic accessories, computer accessories, home electrical products, and personal security and surveillance products. The company is also an active member of the Consumer Electronics Association (CEA).
- Manufacturer Part #: 24770
- Power: 120VAC, 60Hz
- Signal (Frequency): 908.42 MHz (U.S.)
- Protocol: Z-Wave Plus
- Maximum Loads: 960W incandescent, 1/2 HP Motor or 1800W (15A) Resistive
- Wireless Range: Up to 150 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module.
- Operating Temperature Range: 32° to 104°F (0° to 40°C)
- Environmental: For indoor use only.
- Approvals: FCC, IC
- Warranty: 2 Years
This Z-Wave device has advanced features that allow you to customize your experience. These features can be adjusted by a Z-Wave enabled controller that supports the Z-Wave Configuration command class.