Yale Assure Lock YRC216 — Electronic Interconnected Push Button Installation & Programming

Complete installation and programming instructions for the Yale Assure Lock Electronic Interconnected Push Button (YRC216) — covering door prep, mechanical installation, PIN code programming, and optional Z-Wave Plus / ZigBee / iM1 network module setup.

Overview

The Yale Assure Lock YRC216 is an interconnected push-button electronic deadbolt/lever lock available in 4" or 5.5" touchscreen keypad sizes. It supports an optional Network Module (Z-Wave Plus, ZigBee, or iM1) for smart home integration. Retrofitting or modifying this product may impact fire rating, safety features, and warranty — always consult local code specifications to ensure compliance.

Installation Overview

Full step-by-step installation instructions are also available via the free BILT app, which walks through the process visually. The printed instructions cover the following steps:

1. Mark door reference lines and prepare the door (drill through-holes for the lock body and bolt, drilling halfway from each side to prevent splitting).
2. Install the strike plates in the door frame.
3. Determine the door handing (LH, LHR, RH, or RHR) from the secure side of the door.
4. Change the handing of the lock if needed (4" Left Hand to Right Hand conversion shown as an example) — do not tamper with or loosen the E-clip assembly or the 6 screws under the cover.
5. Install the deadbolt and latchbolt, then test their operation before proceeding.
6. Attach the cable assembly, routing it as shown to avoid interference with lock movement; verify cables are securely connected. Two #6-32 x 1/2" pan-head screws must be used to qualify for UL listing.
7. Install the interior lock body, matching orientation and adjusting the thumbturn slot orientation as needed before fastening to the back plate.
8. Install the interior lever (should "snap" into place — pull to confirm it's secure).
9. Test final latchbolt and deadbolt operation. If testing fails, return to the interior lock installation step and recheck the installation.
10. Install the optional Network Module — never install it with batteries already in the unit, as this can cause damage.
11. Install batteries and replace the cover. The bolt must be in the retracted (unlocked) position before installing batteries.

Handing the Lock

After installing batteries and cover, or after a factory reset, you must first create a Master PIN code (see Programming Instructions below). Then:

1. Enter the Master PIN code and press the menu key.
2. Select Advanced Lock Settings.
3. Select "Handing the Lock."
4. Confirm — the lock will automatically cycle its motor to complete handing.

Hardware Troubleshooting

Replacing the Cylinder

1. Remove keypad from door.
2. Remove rubber gasket.
3. Remove the two screws holding the plastic guide in place, then remove the guide.
4. Remove the screw with washer holding the cylinder in place (visible after removing the plastic guide).
5. Remove the cylinder housing by pulling the cylinder tailpiece away from the keypad.
6. To install a new cylinder, reverse the steps above.

Programming Instructions

Maximum User Codes: 250 with a Z-Wave Plus or ZigBee network module; 25 without a network module or with an iM1 module; 12 with Bluetooth.

1. Creating the Master PIN Code

Required upon installation or after a factory reset — the lock cannot be programmed or used until this step is completed. Press the menu key, then the settings key, enter a 4–8 digit Master PIN code, and confirm.

2. Creating User PIN Codes

The Master PIN code must be created first. Enter the Master PIN code, press the menu/enter keys, then enter a 4–8 digit User PIN code and confirm.

3. Unlocking the Door with a PIN Code

Enter the PIN code and press "Unlock."

Resetting the Lock to Factory Default

Warning: resetting deletes all user codes, including the Master PIN, and restores all programming features to factory defaults.

1. Remove the battery cover and batteries.
2. Remove the interior lock to access the reset button hole.
3. Re-insert 3 batteries and insert a small screwdriver into the reset hole, holding the button for 3 seconds.
4. While still holding the reset button, insert the 4th battery and hold for an additional 3 seconds, then release.
5. Re-install the interior lock onto the door.

For best results, the lock should remain installed on the door during a factory reset. Master PIN code creation is the only option available immediately after reset, and must be completed before any other programming.

Factory Default Settings

Key Feature Definitions

• All Code Lockout Mode: Enabled by the Master code; restricts all user (except Master) PIN code access. The keypad flashes 8 times and the lock beeps 3 times when a code is attempted during lockout.
• Audio Mode: Disable to shut off code-confirmation tones for quiet areas.
• Automatic Re-lock Time: After a successful unlock, the lock re-locks automatically after the selected duration (set in Advanced Lock Settings).
• Handing the Lock: Refers to which direction the bolt extends (right or left); the lock may need adjusting if programmed off the door.
• Inside Indicator Light: Shows the active locked status on the interior lock; enable/disable in Advanced Lock Settings.
• Low Battery: The Status Indicator flashes RED when battery power is low. If power is completely lost, use the cylinder key override.
• Master PIN Code: Used for programming and feature settings; also operates (locks/unlocks) the lock. Must be created before any other programming.
• Network Module Setting: Available through Main Menu option 7 when a Network Module is installed; allows the lock to join a network controller.
• One Touch Locking: When enabled, activating the keypad while the latch is retracted extends the latch. When disabled, any valid PIN code re-locks the lock.
• Privacy Mode: Press the privacy button for 4 seconds to disable all PIN codes (do-not-disturb mode).
• Shutdown Time: The unit shuts down for 60 seconds after the wrong-code entry limit is reached.
• Tamper Alert: Sounds an audible alarm if someone attempts to forcibly remove the outside lock from the door.
• User PIN Code: Operates the lock; up to 250 codes with Z-Wave Plus/ZigBee, 25 without a network module or with iM1, or 12 with Bluetooth.
• Wrong Code Entry Limit: After 5 unsuccessful PIN attempts, the unit shuts down for 60 seconds.

Feature Programming Menu (Master PIN Required)

Enter the 4–8 digit Master PIN code followed by the menu key, then enter the digit corresponding to the desired function followed by the menu key again:

• 1 — Master PIN Code Setting
• 2 — User Codes: Enter or Delete individual user codes.
• 3 — Advanced Lock Settings: Automatic Re-lock (Disable / 30 sec / 60 sec / 2 min / 3 min), Inside Indicator Light (Enable/Disable), One Touch Locking (Enable/Disable), Privacy Button Setting (Enable/Disable), Handing the Lock (auto).
• Audio Mode: Enable / Disable (choose Disable for quiet areas).
• All Code Lockout Mode: Enable / Disable.
• Network Setting (appears only with a network module installed): Join the network / Exit the network.
• Set-up Digital Keys.

Programming Troubleshooting

Tip: When batteries are replaced on a network-connected lock, verify the real-time clock date/time (especially around Daylight Saving Time changes).

Optional Network Modules

Z-Wave Plus Module

Remove batteries before removing/inserting the Network Module, then reinstall batteries and cover. This is a security-enabled Z-Wave Plus product using encrypted messages, and must be used with a Security Enabled Z-Wave Controller to access all features. It is interoperable with other Z-Wave certified devices; non-battery nodes act as repeaters regardless of vendor.

• To Enroll (Inclusion Mode): Enter the Master PIN code + menu key, then the appropriate menu keys to join the network.
• To Unenroll (Exclusion Mode): Enter the Master PIN code + menu key, then the appropriate menu keys to exit the network.

Specific Z-Wave Plus association and parameter details are available at YaleHome.com/ZwavePlus. Module: YRMZW2-US, FCC ID U4A-YRHCPZW0FM.

ZigBee Module

Same battery-removal precaution applies. This is a security-enabled ZigBee product requiring a Security Enabled ZigBee Controller for full functionality, and is interoperable with other ZigBee-certified devices.

• To Enroll: Enter Master PIN + menu key, then the appropriate menu keys.
• To Unenroll: Enter Master PIN + menu key, then the appropriate menu keys.

Module: YRMZB2, FCC ID U4A-YRHCPZB0FM. This device should be operated with a minimum distance of 20cm between the radiator and your body.

iM1 Network Module

Must be used with a Yale Assure Lock or Yale nexTouch Lock, and cannot be combined with any other Yale Network Module. Remove batteries before installing/removing the module.

• To Enroll: Enter the Master PIN code + menu key, then the appropriate menu keys.

Connecting the Yale Secure App (with iM1 Module)

1. After enrolling the iM1 module, download the Yale Secure app from the App Store.
2. Enable Bluetooth on your iPhone, iPad, or iPod touch, and stay within a foot of the lock.
3. Open the Yale Secure app and allow it to access your Home Data.
4. Create a new home if you don't already have one, then tap + to add a new Yale Lock.
5. The app searches for your lock — stay within about two feet. When "Yale Lock" appears, tap to add. (If it doesn't appear, enter your Master PIN on the keypad, tap the gear, tap 7, tap gear, tap 1, tap gear.)
6. Scan the Accessory Setup Code printed on the lock, or enter it manually in the app.

Compliance

This equipment has been tested and complies with FCC Part 15 Class B limits (main unit) and applicable Industry Canada regulations. Changes or modifications not expressly approved by Yale Security Inc. could void the user's authority to operate the equipment.

Support

Product Support: 1-855-213-5841 or yalehome.com.