Menu
0
0

Your Cart is Empty

Add description, images, menus and links to your mega menu

A column with no settings can be used as a spacer

Link to your collections, sales and even external links

Add up to five columns

  • Add description, images, menus and links to your mega menu

  • A column with no settings can be used as a spacer

  • Link to your collections, sales and even external links

  • Add up to five columns

    • Home  / Product Manuals & Documentation
    Previous  / Next

    SkylinkHome Snap-On Remote (TM-318) — User Instructions

    August 31, 2026 3 min read

    Full instruction manual for the SkylinkHome™ Snap-On Remote, Model TM-318, covering programming, on/off and dimming operation, and erasing transmitters from receiver modules.

    💾 Download Original PDF 🛒 View Product
    Full text manual (for reference)

    Full instruction manual for the SkylinkHome™ Snap-On Remote, Model TM-318 — a wireless transmitter that snaps directly onto compatible SkylinkHome wall switches/dimmers or works standalone with any SkylinkHome receiver module.

    What's in the Box

    • Snap-On Remote (TM-318)
    • Lithium Battery CR-2032 (pre-installed)
    • User's Instructions

    Powering Up

    Remove the battery isolator tab from the transmitter. The red LED stays on for 15 seconds, then turns off. Press the button — the red LED should flash to confirm the transmitter is powered. If the LED does not flash, see the Battery section below.

    Programming to a Receiver Module

    1. Put the target receiver module into programming mode (refer to that receiver's own instructions).
    2. Remove the battery and battery holder from the Snap-On Remote.
    3. Re-insert the battery and holder (positive side with battery marking faces down) — the red LED stays on steadily for 15 seconds.
    4. Press the button on the remote while the LED is steadily on to transmit the "Learn" code.
    5. Once programmed, the receiver exits programming mode and the transmitter is ready to use.

    Note: Once the receiver enters programming mode, complete the pairing quickly — it automatically exits programming mode after 15 seconds even if pairing hasn't finished.

    Basic Operation

    On/Off

    Pressing the button once toggles the connected load — if the light is off, pressing turns it on, and vice versa.

    Brightness Control (Dimmable Loads Only)

    With the light on, press and hold the button to adjust brightness. Hold until the desired level is reached, then release. Press and hold again to change brightness in the opposite direction.

    Erasing Transmitters from a Receiver

    There are two erase methods depending on the receiver model:

    Type Compatible Receivers Procedure
    A) Self Erase PL-318, PR-318, PA-318, LS-318, WR-001 Press the erase button on the receiver itself — this clears all paired transmitters. No transmitter action needed.
    B) Erase by Remote LX-318, MD-318, MR-318, WE-001 Remove and re-insert the battery holder. Press and hold the button for at least 2 seconds while the LED is steadily on to transmit the "Erase" code. Put the receiver into programming mode; once it confirms the erase, release the button.

    Battery Replacement

    Replace the battery (CR-2032) when the operating range decreases or the red LED no longer flashes during use — follow the same steps as the initial battery installation. Dispose of old batteries promptly and properly.

    FCC Compliance

    This device complies with Part 15 of the FCC Rules. Operation is subject to: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

    Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

    Warranty

    Within one year of purchase, if this product becomes defective (excluding battery) due to faulty workmanship or materials, it will be repaired or replaced at no charge. Proof of purchase and a Return Authorization are required.

    Accessories

    The SkylinkHome™ System includes SkylinkPad™ Remotes, Motion Sensors, ON/OFF Wall Switches, Wall Dimmers, Plug-In Dimmers (with/without Repeater), Plug-In ON/OFF Controls (Indoor/Outdoor), Screw-In Dimmers, and Smart Button™ Garage Door Controls. Visit skylinkhome.com for details.

    Customer Service

    SkylinkHome: 1-800-304-1187 (Mon–Fri, 9am–5pm EST) | support@skylinkhome.com | www.skylinkhome.com