SECO-LARM MVE-AT11-01NQ / MVE-AT11-W1NQ — Enhanced Extenders for HDMI over Single Cat5e/6 Manual

Full manual for the SECO-LARM ENFORCER MVE-AT11-01NQ / MVE-AT11-W1NQ Enhanced Extenders for HDMI over Single Cat5e/6 — tabletop and wall-plate models for extending HDMI up to 230ft.

Overview

These ENFORCER extenders send HDMI video and audio signals over a single Cat5e/6 cable using an active transmitter and receiver, reaching up to 230ft (70m) at 1080p with zero signal loss. Choose the tabletop model (MVE-AT11-01NQ) or the double-gang wall-plate model (MVE-AT11-W1NQ) — both are cross-compatible, so you can mix and match a transmitter from one model with the receiver of the other. IR pass-through is included so a remote control can operate a device (TV, media player, etc.) at the opposite end of the run.

Key Features

• Signal strength: Active operation keeps the signal strong over the full cable length.
• Distance: Transmits a clear HDMI signal up to 230ft (70m).
• Formats supported: Progressive and interlaced — 1080p/1080i/720p/576p/576i/480p/480i.
• Plug and play: Complete set with transmitter, receiver, power supplies, and IR adapters — no configuration needed.
• Zero signal loss: Integrated circuits clean, buffer, and amplify the HDMI signal along the entire run.
• Connect multiple units: Repeat up to four sets to extend range to 918ft (280m).
• Mix and match: Tabletop and wall-plate transmitters/receivers are interchangeable.

Specifications

Status LED Chart

What's Included

• 1x Transmitter
• 1x Receiver
• 2x 5VDC power adapters
• 1x IR Transmitter
• 1x IR Receiver
• 1x Manual

Installation

1. Determine where the transmitter and receiver will be wired and how much Cat5e/6 cable is needed.
2. Connect an HDMI cable between the transmitter and the source device.
3. Connect an HDMI cable between the receiver and the display.
4. Connect a Cat5e/6 cable between the receiver and transmitter units (Cat6 recommended for best results).
5. Connect a 5VDC adapter to the transmitter and another to the receiver.
6. To use remote control pass-through: install the IR transmitter to the IR-TX port of the closest extender unit (pointing at the target device), and install the IR receiver to the IR-RX port on the other extender unit. Point the remote control at the IR receiver when in use.
7. MVE-AT11-W1NQ only: install using a standard double-gang box.
8. Switch on the HDMI source and display to verify proper operation.

Troubleshooting

If the HDMI device doesn't function correctly:

• Confirm T568-B wiring standard was used
• Make sure the extender is powered on both ends
• Make sure the source and display are both powered
• Test the Cat5e/6 cable between receiver and transmitter for functionality
• Rule out HDMI source/cable/display issues by plugging the source directly into the display
• Confirm transmitter and receiver are plugged into the correct units
• Confirm the HDMI source is compatible with the HDMI display

Warranty

This SECO-LARM product is warranted against defects in material and workmanship for one (1) year from the date of sale to the original consumer customer under normal service. The warranty is void if damage results from acts of God, misuse, abuse, neglect, unauthorized repair or alteration, improper/abnormal usage, or faulty installation. SECO-LARM's sole obligation is limited to repair or replacement at its option; SECO-LARM is not liable for special, collateral, incidental, or consequential damages.

Manufacturer: SECO-LARM U.S.A., Inc., 16842 Millikan Avenue, Irvine, CA 92606 · (949) 261-2999 / (800) 662-0800 · sales@seco-larm.com · www.seco-larm.com