Menu
0
0

Your Cart is Empty

Add description, images, menus and links to your mega menu

A column with no settings can be used as a spacer

Link to your collections, sales and even external links

Add up to five columns

  • Add description, images, menus and links to your mega menu

  • A column with no settings can be used as a spacer

  • Link to your collections, sales and even external links

  • Add up to five columns

    • Home  / Product Manuals & Documentation
    Previous  / Next

    SECO-LARM Enforcer HDMI Extender over Single Cat5e/6 (MVE-AH1E1-01NQ) — Manual

    August 31, 2026 3 min read

    SECO-LARM Enforcer HDMI Extender over Single Cat5e/6 (MVE-AH1E1-01NQ) — Manual

    💾 Download Original PDF 🛒 View Product
    Full text manual (for reference)

    Manual for the SECO-LARM ENFORCER® HDMI Extender over Single Cat5e/6 (model MVE-AH1E1-01NQ) — an active HDMI transmitter/receiver pair that sends HDMI video and audio over a single run of Cat5e/6 cable up to 164 feet (50m), with IR pass-through for remote control extension.

    Features

    • Extends HDMI over a single Cat5e/6 cable with zero signal loss up to 164ft (50m) at 1080p.
    • Supports 480i through 1080p resolutions.
    • HDMI loop output for a local display at the source location.
    • Plug-and-play — ships as a complete set.
    • IR pass-through for remote control of source/display devices.
    • EDID management switch to match display settings to source device.
    • Two 5VDC power supplies included.

    Parts List

    • 1x Transmitter (MVE-AH1E1-01NTQ)
    • 1x Receiver (MVE-AH1E1-01NRQ)
    • 2x 5VDC power adapters
    • 1x IR Transmitter (with double-sided tape)
    • 1x IR Receiver (with double-sided tape)
    • 1x Manual

    Specifications

    Video formats High-speed HDMI, HDCP 1.2, 1080p/1080i/720p/576p/576i/480p/480i
    Audio formats LPCM, Dolby-AC3, DTS 7.1, DSD
    Deep color 24-bit
    Range at 1080p Up to 164ft (50m)
    Video amplifier bandwidth 4.95Gbps
    Cat5e/6 wiring standard T-568B
    IR pass-through frequency 30–60 kHz
    Power supply 1A @ 5VDC (2 adapters), 2.1mm plug
    Current draw Transmitter: 300mA @ 5VDC · Receiver: 200mA @ 5VDC
    Operating temperature 32°–104°F (0°–40°C)
    Operating humidity 20–90% RH, non-condensing
    Dimensions 3-1/8" x 11/16" x 2-5/8" (79 x 17 x 67mm) each
    Weight 5.3 oz (150g) each

    HDMI Loop Output

    The transmitter includes a secondary HDMI output for driving a local display in the same room as the HDMI source.

    EDID Settings

    An EDID management switch matches display settings to the source device, useful when the display isn't showing an image correctly. Position 1 (default) copies the transmitter's HDMI loop display EDID to the source; Position 2 copies the receiver's HDMI display EDID to the source instead.

    Equalizer DIP Switch Settings

    DIP switches on the receiver adjust signal strength/noise compensation based on cable run length, from 0–24ft up through 148–164ft, in roughly 25ft increments — refer to the chart in the printed manual to match the switch position to your actual cable length.

    IR Pass-Through

    Supports one-way IR pass-through (30–60 kHz) for remote operation of the source device from the display location. Install the IR transmitter pointed at the device to be controlled, and the IR receiver pointed toward where the remote will be used.

    Installation Steps

    1. Determine transmitter/receiver locations and the required Cat5e/6 cable length.
    2. Connect the transmitter to the HDMI output of the source device.
    3. Run and connect the Cat5e/6 cable between the transmitter and receiver.
    4. Connect the receiver to the HDMI input of the display.
    5. Connect a 5VDC adapter to each unit.
    6. If using IR control, install the IR transmitter at the IR-TX port and the IR receiver at the IR-RX port, using the supplied double-sided tape.
    7. Power on the source and display to verify correct operation. If the image doesn't display correctly, try the other EDID switch position.
    8. If the display flickers, blinks, or shows distortion, adjust the Equalizer DIP switch to match your cable length range.

    Troubleshooting

    Symptom Fix
    HDMI device does not function correctly Confirm T568-B wiring; confirm both extender units are powered; confirm source/display are powered; test the Cat5e/6 cable directly; test the HDMI source/cable/display by connecting them directly together
    Screen flickering or brief image loss Use higher-grade cable (Cat6 recommended); lower the source's HDMI output resolution (e.g. 1080p→1080i); power down, flip the EDID switch, and re-power; or restart the full handshake by powering everything down and back up in sequence, starting with the HDMI source

    Warranty

    SECO-LARM warrants this product against defects in material and workmanship in normal service for one (1) year from date of sale to the original customer. SECO-LARM's obligation is limited to repair or replacement of defective parts (transportation prepaid by customer). The warranty is void for damage from acts of God, misuse/abuse, neglect, unauthorized repair/alteration, improper usage, or faulty installation. SECO-LARM is not liable for special, collateral, incidental, or consequential damages.

    SECO-LARM U.S.A., Inc. · 16842 Millikan Avenue, Irvine, CA 92606 · Phone: (949) 261-2999 / (800) 662-0800 · www.seco-larm.com