Menu
0
0

Your Cart is Empty

Add description, images, menus and links to your mega menu

A column with no settings can be used as a spacer

Link to your collections, sales and even external links

Add up to five columns

  • Add description, images, menus and links to your mega menu

  • A column with no settings can be used as a spacer

  • Link to your collections, sales and even external links

  • Add up to five columns

    • Home  / Product Manuals & Documentation
    Previous  / Next

    Luxul Managed PoE Switch (SW-510/SW-610-48P-F) — Setup Guide

    August 31, 2026 3 min read

    Setup guide for Luxul Managed PoE Switches (SW-510-48P-F / SW-610-48P-F) — initial setup, default login credentials, LED status indicators, PoE power budgets, and factory reset instructions.

    💾 Download Original PDF
    Full text manual (for reference)

    Setup guide for Luxul Managed PoE Switches (SW-510-48P-F and SW-610-48P-F) — 48-port PoE+ managed gigabit switches with Gigabit SFP or 10-Gigabit SFP+ uplink ports. Covers initial setup, default login, LED indicators, and factory reset.

    Setting Up Your Switch

    1. Place your switch in a rack or on a desktop.
    2. Connect one Ethernet cable from your router (or other switch) to any port on the switch. Connect the included power cable from your switch to your power source. Note: Minimum boot time is 60 seconds.
    3. The default IP address method is DHCP with a fixed failover of 192.168.0.4. Locate your switch's IP address via your router's Connected Client list (or similar), then log in with:
      • Username: admin
      • Password: admin
      Note: If your computer/device isn't set to obtain an IP automatically, set a temporary static IP in the 192.168.0.X range with subnet mask 255.255.255.0 (default gateway can be left blank).

    Product Descriptions

    • SW-510-48P-F — 48 PoE+ ports with (4) Gigabit SFP ports, Managed Gigabit Switch
    • SW-610-48P-F — 48 PoE+ ports with (4) 10 Gigabit SFP+ ports, Managed Gigabit Switch

    LED Indicators

    Indicator State Description
    System Blinking Normal operation
    System On Switch is booting
    System Red Contact support
    System Off Power disconnected
    Ethernet Port Link/Act Status* Green 1000Mbps device connected to port
    Ethernet Port Link/Act Status* Amber 10/100Mbps device connected to port
    Ethernet Port Link/Act Status* Blinking Data being transferred
    Ethernet Port Link/Act Status* Off No device connected
    Ethernet Port PoE Status* Green Switch providing PoE power to connected device
    Ethernet Port PoE Status* Amber PoE power limit exceeded
    Ethernet Port PoE Status* Blinking PoE fault error
    Ethernet Port PoE Status* Off No PoE device connected
    SFP Port Status Green 1Gbps connection
    SFP Port Status Blue** 10Gbps connection

    * Quickly press and release the MODE/RESET button to switch the LEDs between LINK/ACT and PoE status.
    ** Applies only to SW-610-XX models.

    PoE Power Budget

    Model PoE Budget Power Input Rating (on product label)
    SW-510-48P-F 740W AC100-240V~50/60Hz 12A
    SW-610-48P-F 740W AC100-240V~50/60Hz 12A

    Do not exceed the PoE budget for your model. Not suitable for use in locations where children are likely to be present. Intended for indoor use only — all Ethernet cables are for intra-building connection only; do not connect these ports directly to wiring that exits the building.

    FAQ — What If...

    I need to restore factory default settings?

    Hold the button labeled MODE/RESET for longer than 7 seconds. The switch will reboot once the button is released. Reboot takes approximately 60 seconds before the UI becomes available. If a DHCP server is not available, the failover IP becomes active 60 seconds after boot completes.

    I need to restart my switch?

    Unplug the power cable, OR hold the MODE/RESET button for 2–7 seconds, OR use the Reboot function in the Administration tab of the UI.

    I want to perform advanced configuration?

    Use the default DHCP address (with fixed failover 192.168.0.4) to find your switch's IP via your router's Connected Client list, then log in with the default admin/admin credentials.

    Important: Changes made to the switch's configuration must be saved or they will be lost on reboot. Go to Administration > Configuration > Save startup-config and Save Configuration.

    Support

    Technical Support: 801-822-5450 / support@luxul.com
    Sales: 801-822-5450 / sales@luxul.com
    Support chat is available via LegrandAV.com's "Live Chat" (select Luxul under 'Brand').