HAI 58A00-1 Mini Door/Window Transmitter — Installation Instructions

HAI 58A00-1 — Mini Door/Window Transmitter Installation Instructions

Document Number: 58I00-1. The 58A00-1 Mini Door/Window Transmitter is a mini-sized, supervised wireless contact that works with the HAI 45A00-1 Wireless Receiver.

Powering the 58A00-1

The 58A00-1 comes with the battery preinstalled. To activate, hold the 58A00-1 firmly in one hand and pull the plastic tab in the direction indicated.

Locating the Transmitter

Select the location where the 58A00-1 is to be mounted.

Note: RF signals can be affected by metal objects, including metal doors or large mirrors. Such locations should be avoided, as they can interfere with proper operation.

Mounting the 58A00-1

Once you have determined the proper location, the 58A00-1 can be permanently mounted.

Note: It is the responsibility of the installer to ensure that the 58A00-1 is securely mounted in the intended location.

Using Provided Screws

Remove the back from the transmitter. Mount the back housing of the 58A00-1, using the screws supplied, to the desired location.

Using Adhesive Tape

Ensure the surface is clean and dry. Apply the supplied tape to the back of the 58A00-1, press and hold firmly in the desired location for approximately 10-15 seconds. It can take up to 24 hours for the tape to reach maximum bonding strength.

Align the magnet with the notched arrow on the 58A00-1 housing. Mount the magnet a maximum of 0.4" (1.8 cm) from the 58A00-1 using the provided tape or screws. If necessary, use the spacers provided. Once the 58A00-1 and magnet are mounted, open and close the window/door to ensure that none of the parts interfere with this movement. Only one magnet can be used for each 58A00-1.

Enrolling the 58A00-1

To enroll the 58A00-1, put the 45A00-1 Wireless Receiver into Setup mode and advance to an unused address location. Activate the reed switch by removing the magnet from the transmitter for 1 second, then replacing it. Refer to the Installation Instructions for the 45A00-1 for additional information.

Tamper Switch

Out of the box, the 58A00-1 comes equipped with case tamper detection — if the case is removed, the 58A00-1 will report a zone tamper to the controller.

For added security, the 58A00-1 was also designed to provide wall tamper monitoring. Simply replace the short rubber actuator with the longer one included. With this option, if the case is opened or if the 58A00-1 is removed from its location, a tamper signal will be sent to the controller. It is strongly recommended that mounting screws be used when using the wall tamper option.

Replacing the Battery

The 58A00-1 requires one Renata CR2450N lithium battery. To replace the battery, remove the cover. Once the cover is removed, the battery will be visible. To remove the battery, insert a flathead screwdriver under the battery and gently twist.

Warning: Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire.

FCC Statement

This equipment has been tested to FCC requirements and found acceptable for use. It has been type tested and found to comply with the limits for a Class B computing device per Part 15 of the FCC Rules, designed to provide reasonable protection against interference in a residential installation. If this equipment causes interference to radio or television reception, try: using a quality outdoor antenna, reorienting the receiving antenna, moving the receiver away from the control/communicator, moving antenna leads away from wire runs, or plugging the controller into a different branch circuit outlet.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.