GE Z-Wave 45605 — Wireless Controlled Duplex Receptacle Manual

Manual for the GE Z-Wave 45605 Wireless Controlled Duplex Receptacle (SmartHome™) — a dual-outlet in-wall receptacle with one always-on outlet and one Z-Wave controlled outlet for wireless lighting/appliance control.

Introduction

Z-Wave technology automates lighting/home control and provides easy remote operation of Z-Wave compatible devices. This duplex receptacle is one component of a Z-Wave control system, designed to work with all other Z-Wave compatible devices in a home control network. It also acts as a wireless repeater, extending the range of your wireless controller for commands intended for other devices on the network.

Caution: This device must be installed in accordance with the National Electrical Code and local regulations in the US, or the Canadian Electrical Code and local regulations in Canada. If you're not confident performing the installation, consult a qualified electrician.

Load limit: the device connected to the Z-Wave controlled outlet must not exceed 600W (incandescent), 15A/1800W (resistive), or ½ HP (motor). Maximum combined load for both outlets is 1800W (15A) resistive. Do not attempt to repair internal parts of this unit.

Warning: Risk of Fire, Electrical Shock, Burns

Controlling Appliances — Safety Guidance

Exercise extreme caution when using Z-Wave devices to control appliances, since the controlling device may be operated from a different room than the appliance, and accidental activation is possible if the wrong remote button is pressed. Z-Wave devices can also turn on automatically due to scheduled events, which — depending on the appliance type — could create a hazardous situation. Recommendations:

• Assign Z-Wave controlled appliances to device numbers 10-18 on the GE remote — this requires pressing "Shift" first, significantly reducing accidental activation.
• Remove appliance-controlling Z-Wave devices from the "All" control configuration (see your GE remote's manual for instructions).
• Do not include appliance-controlling Z-Wave devices in groups or scenes.
• Do not use Z-Wave devices to control electric heaters or other appliances where automatic, unattended, or accidental power-on could be hazardous.
• Double-check programs for accuracy before use.

Not for use with medical or life support equipment. Z-Wave enabled devices should never be used to supply power to, or control the on/off status of, medical or life support equipment.

Wireless Range

This device complies with the Z-Wave standard of 65 feet (20m) open-air, direct antenna-to-antenna transmission. Actual home performance depends on the number of walls between the controller and target device, construction type, and the number of Z-Wave devices in the network. Each Z-Wave device acts as a signal repeater, and multiple devices create more possible transmission paths, helping eliminate RF "dead zones."

Each wall/obstacle reduces max range ~25-30%. Brick/tile/concrete blocks more signal than wood-frame/drywall. Metal junction boxes cause ~20% additional signal loss. Z-Wave coexists with 802.11 Wi-Fi, Bluetooth, and other 2.4/5.8GHz devices; some 900MHz baby monitors, wireless video devices, or older cordless phones may interfere — try switching those devices' A/B channel if available.

Installation

This receptacle can be used in new installations or to replace an existing wall receptacle. A wall plate is not included — reuse your existing wall plate if replacing a standard decorative duplex receptacle, or use a medium decorative wall plate (available at most hardware/home stores) for new installations.

Wire connections: Green or bare (ground), Black (energized/hot), White (neutral).

1. Cut power to the circuit at the fuse box or breaker.
2. Remove the wall plate.
3. Warning: Before continuing, confirm no power is reaching the receptacle.
4. Remove the mounting screws for the receptacle.
5. Remove the receptacle from the box.
6. Disconnect the wires from the old receptacle.
7. Connect the Z-Wave receptacle as illustrated in the wiring diagram (green/bare to ground, black to hot, white to neutral).
8. Insert the Z-Wave receptacle into the box, ensuring the wires aren't pinched or crushed.
9. Secure the receptacle to the box with the supplied screws.
10. Reattach the wall plate.
11. Restore power to the circuit at the fuse box or breaker, then test the system.

Wiring Notes

Always follow recommendations on insulation strip length and wire combinations. The included wire connectors are designed for copper wire only — consult a qualified electrician if you have aluminum wiring.

1. Strip 3/8" of insulation for 12 or 14 AWG cable; strip 7/16" for 16 or 18 AWG cable.
2. Keep stripped ends parallel and align frayed strands (do not twist the wires).
3. Push the wires firmly into the connector, turn the connector clockwise until tight, then pull to confirm they don't loosen.

Key Features

• One AC outlet remotely controlled via Z-Wave
• Remote on/off control with the Z-Wave controller/network
• Manual on/off control via the front panel pushbutton
• One always-on AC pass-through outlet

Basic Operation

The connected light can be turned ON in two ways: (1) with a remote control, or (2) manually using the pushbutton on the Z-Wave receptacle. GE Z-Wave remotes control individual devices, groups, and scenes — other Z-Wave certified remotes may offer less configuration flexibility.

Manual Control

1. Press the button to manually toggle the connected equipment on or off (it's a toggle — if OFF, pressing turns it ON, and vice versa).
2. Include or exclude the receptacle from the Z-Wave network via your primary controller: when prompted by the controller's network setup function, press and release the button. The controller should confirm success; repeat if it indicates failure. The same procedure adds the receptacle to groups or scenes.

Note: after a power failure, the 45605 receptacle returns to its last used on/off state.

LED Indicator: The LED remains lit when the Z-Wave outlet is OFF (factory default) — this can be changed via node configuration if your controller supports it (see Advanced Operation).

Advanced Operation

These parameters require an advanced controller (e.g. the 45601 Advanced remote) — basic remotes cannot change these settings.

All On / All Off

Depending on your primary controller, the receptacle can be configured to respond to ALL ON / ALL OFF commands in up to four ways: respond to both (default), respond to neither, respond to ALL OFF only, or respond to ALL ON only.

LED Behavior

By default, the LED turns ON when the connected outlet is OFF. To make the LED turn ON when the outlet is ON instead, change parameter 3 to "1" (parameter #3, length 1 byte, valid values 0 or 1, default 0).

Restoring Factory Defaults

All network settings and configuration parameters reset to factory defaults when the device is deleted from the network via your primary controller.

Over-Current Protection

Provided by an internal, non-user-serviceable fuse. Check your home's circuit breakers before concluding the product needs replacement.

Interoperability with Z-Wave Devices

A Z-Wave network can integrate devices of various classes from different manufacturers, but your controller must include the appropriate device classification to control non-lighting devices. For example, the basic GE 45600 remote only controls lighting-class Z-Wave devices, while the GE 45601 Deluxe remote (with LCD) can also control other classes such as thermostats.

Specifications

Compliance

FCC ID: U2Z45605. This equipment complies with FCC Part 15 Class B digital device limits, providing reasonable protection against harmful interference in residential installations. Operation is subject to the condition that it must accept any interference received, including interference that may cause undesired operation. No modifications to the antenna or device are permitted — doing so could void the user's authority to operate the equipment under FCC RF exposure requirements.

IC: 6924A-45605. This Class B digital device complies with Canadian ICES-003.

Warranty

JASCO Products Company warrants this product against manufacturing defects for two years from the original purchase date, limited to repair or replacement — excludes consequential/incidental damage to other products used with the unit. Contact Customer Service at 800-654-8483 (option 4), 7:30 AM–5:00 PM CST, or via www.jascoproducts.com.

JASCO Products Company, Building B, 10 E Memorial Rd., Oklahoma City, OK 73114. Z-Wave is a trademark of Zensys A/S. GE and the GE monogram are trademarks of General Electric Company, used under license by Jasco Products Company LLC. Made in China. © 2009 JASCO Products Company. Model 45605-2 / ZW1001