FortrezZ FTS05x Wireless Flood & Temperature Sensor — User Manual

Overview

The FortrezZ FTS05x is a Z-Wave Plus Security-enabled Wireless Flood and Temperature Sensor. It detects water leaks and measures temperature, sending alerts on the Z-Wave network when a leak or a high/low temperature condition occurs. It comes in four part-number variants: FTS05LB-yy / FTS05LW-yy (battery-only, black/white case) and FTS05PLB-yy / FTS05PLW-yy (battery/AC version with a water/temperature probe, black/white case).

Specifications

Warnings and Precautions

• Do not store highly flammable items such as oily rags or other combustibles near the FTS05x.
• Do not apply electrical power to the unit unless it is fully assembled.
• Install in accordance with electrical codes and regulations; consult an electrician or Z-Wave home automation specialist if unsure.
• The FTS05x must not be used in life support and/or safety applications. As with any RF device, wireless transmissions can be subject to interference or loss of communication, and the end-user is responsible for ensuring the device meets their requirements.
• Do not place near metal objects — this decreases range and/or blocks wireless transmissions.

Using the FTS05x in a Z-Wave Network

Add (Inclusion): Set the controller into Add/Inclusion mode, then briefly press the switch once. The controller will confirm the unit was added, and the LED will blink.

Remove (Exclusion): Set the controller into Remove/Exclusion mode, then press and hold the switch for approx. 2 seconds and release. The controller confirms removal and the LED blinks.

Associations: Once networked, a controller can associate the FTS05x with other devices (a light, a remote audible alarm, etc.). The FTS05x supports eight association groups with a maximum of 2 devices per group.

Wakeup Notification: The FTS05x wakes and sends a status notification every 4 hours by default; a brief switch press while networked also triggers a wake-up notification.

Status LED / Buzzer Indications

Choosing a Mounting Location

The FTS05 is suitable for normally dry, interior locations only. The FTS05P allows the external probe to be submerged. Avoid metal frames or enclosures that could affect RF range, and place the unit so any leaks will not drip directly on it.

Recommended uses: Under sink, next to sump pumps, water heaters, laundry room, bathroom floor, storage area, garage, utility sink, vacation/recreation homes, boats. The FTS05P is also suited to applications needing a maintained water level.

During an Alarm

If water is detected or missing (FTS05P only), or an over/under-temperature condition occurs, the unit sends alert message(s) to the Z-Wave network. If associations are configured, Basic Set messages are sent as described under Associations. If Water/Heat Alarms are configured, the FTS05x sends alert messages to the Lifeline group. Drying (or submerging, on FTS05P) the sensor contacts clears the Water Alarm; an alarm-clear message is likewise sent when temperature returns to normal.

Initial Test

Moisten a paper towel and place it over both small metal pads (FTS05) or both metal prongs (FTS05P probe) until you see two quick LED blinks (may take up to 4–5 seconds). Remove the towel and clean the pads — the LED should blink four times. If the LED fails to blink, check the battery, moisture level, or sensor condition.

Configuring the FTS05x

High/low temperature setpoints can be configured (low must be at least 2°C below high; low cannot be set below -10°C, high cannot exceed 70°C). The FTS05P can be configured for water-detect or water-missing mode. The Basic Set state for association group 2 can be configured to send ON (default) or OFF on a water alarm.

Associations

Caution: More frequent temperature reporting decreases battery life — select only one temperature-report group per device.

Other Program Button Actions

• Factory Reset: Press and hold the program button for >15 seconds. The LED flashes ~30 times when complete. Only use when the primary controller is missing or inoperable — this removes the device from its network and resets all configuration.
• OTA Firmware Update mode: Quickly press the program button 3 times while networked, then activate your controller's update mode. Only start this when a firmware update will begin immediately at the controller; press once to exit OTA mode.

Battery / Low Battery

The FTS05x sends a "Replace Battery Soon" alert at low battery, escalating to "Replace Battery Now" as the battery depletes further, along with periodic LED blinking. After a water leak, ensure there is no residual moisture around the battery. Do not install damaged or unsealed batteries. Use silicone caulk sealant around the screws after replacing batteries to maintain the water seal.

Regulatory

This device complies with Part 15 of the FCC Rules (Contains Transmitter Module FCC ID: WRD-FM5202) and Industry Canada license-exempt RSS standards (Contains IC: 8156A-FM5202). It has also been tested for use in European countries under EN 300 220 (2012-05) and ETSI EN 301 489-1 (2011-09), and complies with the WEEE Directive.

Warranty

FortrezZ, LLC warrants the product to be free from defects in material and workmanship under normal use for one year, and is not responsible for consequential damages or installation costs. Products may be returned to the distributor for exchange or full refund within 30 days of purchase, or returned to FortrezZ with a valid Returned Goods Authorization (RGA) number.