Simply Automated Anywhere Virtual 3-Way Switch Kit (V3WAY-B) — Installation Manual

Installation manual for the Simply Automated Anywhere Virtual 3-Way Switch Kit (2-Rocker), model V3WAY-B — a pair of powerline-communicating switches that provide 3-way virtual lighting control without traveler wires or batteries.

Overview

The kit includes two high-quality, professional-grade on/off switches (models US2-V02 and US1-V01) with gloss white faceplates. They replace existing mechanical switches and use the existing white neutral wire to provide true 3-way control over powerline communication — no traveler wire or batteries needed. It's compatible with Simply Automated's other Anywhere Switches and Accessories (US1-V0, US2-V0, controlled receptacle URD-V0, plug-in UMA-V0, wire-in UFR-V0), but is not compatible with any PC-Configured, Pre-Configured, SimplySmart™, or other UPB/UPStart configured products.

The technology uses safe, reliable powerline communication with no RF emissions — more reliable than X10 — and is even used in freeway bridge applications spanning over a mile.

Key Features

• Virtual ON/OFF control of 2 circuits from 1 switch location; add more locations with model US1-V0, US2-V0, or other Anywhere accessories
• 2-rocker switch: top rocker controls the local circuit (and devices on channel 2); bottom rocker controls the remote switch (and devices on channel 1)
• Compatible with LED, incandescent, halogen, fluorescent, and low-voltage lighting and motors — pump/fan (900W / 7.5A max, 1W min)
• Vapor (sodium/mercury) or metal-halide lights may require isolation filters (model ZNF10A-W)
• Detachable white-rocker faceplates; color-change rocker kits sold separately (models ZS11, ZS22)
• Thermal overload protection — switch momentarily turns off if it overheats, then resumes once cooled

Important Safety Instructions

• DO NOT WIRE HOT — permanent damage may result; improper installation voids the warranty. Pull out the LED indicator light-pipe (1/4") to disconnect power first if needed.
• Switches require hot and neutral connections.
• Installation should be performed by a qualified electrician, per NEC/CEC codes.
• Do not use outdoors (unless moisture-protected), do not cover while in use, keep away from water.
• Do not exceed the maximum load rating, de-rated for multi-gang boxes (see load table below).
• Do not install in areas that can exceed 120°F.
• Do not wire this device to a receptacle — use model URD-V0 controlled receptacle instead.

Load De-Rating Table

Installation Steps

1. Locate the two existing wall switches where the kit will be installed. Check the lamp rating against the de-rating table.
2. Disconnect power at the circuit breaker for each switch circuit.
3. Remove the existing wall switches and disconnect the wires.
4. If changing faceplate color, remove and replace before wiring (see below).
5. At each switch location, wire-nut all white (neutral) wires together — connection must be tight for good powerline communication.
6. Wire-nut the brown (load output) wire of the switch to the black wire of the load/fixture being controlled.
7. Wire-nut the black (line) wire of the switch to the black (line) power wire — again, ensure a tight connection for signal integrity.
8. Mount each switch in its J-box using the captive screws. Do not over-tighten.
9. Reconnect power at the circuit breakers.
10. Tap the top of the rocker to turn on, tap the bottom to turn off (works for the local switch and any linked Anywhere accessories).

Changing Faceplates

To remove: Remove the wall plate, press the top two side-prongs of the rocker faceplate inward to unlatch, then press the two lower side-prongs inward and pull the faceplate away and slightly downward from the switch body.

To install: Align the light pipe recess and the four side prongs with the switch body's slots, then press the faceplate straight on while squeezing the prongs, ensuring all four are fully latched.

Power Disconnection

To power down a switch and its connected fixture, depress the top of the rocker, then pull the underside light-pipe tab out about 0.2" with a fingernail until it stays in place — the LED will extinguish. Push the tab back in to restore power. Use this to prevent damage when wiring hot.

Changing Channels

There are 4 available channels. The US2-V0 transmit channels (1 & 2) are fixed and cannot be changed, but the US1-V0 channel can be changed:

1. Press and hold the rocker down (~6 seconds) until the status LED flashes green, then release.
2. Tap the rocker 2 times for channel #2 (3 times for #3, 4 times for #4). The LED stops flashing.
3. Repeat for other switches/accessories that need to share the same channel.
4. Test that switches communicate and control each other correctly.

Factory reset: Tap the rocker 5 times quickly (LED flashes green), then 10 times quickly (LED flashes blue), then 2 times quickly to stop flashing — the switch is now reset to channel #1.

Troubleshooting

• LEDs not lit on either switch? Check the power disconnect tab is pressed in, and verify hot/neutral wire-nut connections and breaker state.
• LEDs not changing from blue to green when turning on? Check hot/neutral connections for tightness. If LEDs do work correctly, check the brown load wire connection and the fixture/bulb itself.
• Switches not controlling each other despite matching channels? Try phase alignment — swap breakers/wires so both switches are on the same electrical phase (A or B) — or install a phase coupler (model ZPCI).
• For further help: Simply Automated Technical Support, 800-630-9234 / 760-431-2100 ext. 138, or Support@Simply-Automated.com.