Menu
0
0

Your Cart is Empty

Add description, images, menus and links to your mega menu

A column with no settings can be used as a spacer

Link to your collections, sales and even external links

Add up to five columns

  • Add description, images, menus and links to your mega menu

  • A column with no settings can be used as a spacer

  • Link to your collections, sales and even external links

  • Add up to five columns

    • Home  / Product Manuals & Documentation
    Previous  / Next

    SECO-LARM EV-Y2501-A2WWQ / AMWWQ 4-in-1 HD Turret Cameras — Installation Manual

    September 08, 2026 3 min read

    Installation manual for the SECO-LARM ENFORCER EV-Y2501-A2WWQ (fixed lens) and EV-Y2501-AMWWQ (varifocal lens) 4-in-1 HD Turret Cameras with WDR.

    💾 Download Original PDF 🛒 View Product
    Full text manual (for reference)

    Installation manual for the SECO-LARM ENFORCER EV-Y2501-A2WWQ (2.8mm fixed lens) and EV-Y2501-AMWWQ (2.8mm~12mm varifocal lens) 4-in-1 HD Turret Cameras with WDR — 5MP analog cameras supporting TVI, CVI, AHD, and CVBS formats.

    Overview

    These ENFORCER turret cameras offer True Day/Night with ICR Module, True WDR (Wide Dynamic Range), and 3D Digital Noise Reduction in a rugged, vandal-resistant, weatherproof (IP66) housing. Cables are concealed in the mounting bracket to prevent tampering. Both models are 12VDC, white housing.

    Parts List

    • 1x Turret camera
    • 1x Mounting template
    • 3x Mounting screws
    • 1x DC plug
    • 1x Manual

    Specifications

    Spec EV-Y2501-A2WWQ EV-Y2501-AMWWQ
    Type Fixed Turret Camera Varifocal Turret Camera
    Formats TVI (Default) / CVI / AHD / Analog (CVBS)
    CMOS sensor 1/2.8" 5MP Sony CMOS
    Resolution (HD) 2592x1944
    Lens 2.8mm ICR 2.8~12mm ICR
    Viewing angle 128° 37°~134°
    # of IR LEDs 2 (850nm) 4 (850nm)
    IR range Up to 98ft (30m) Up to 115ft (35m)
    F Stop F1.6 F1.8~3.3
    FPS 20FPS
    Minimum illumination 0Lux (IR on); 0.05Lux@F1.2 AGC on (IR off)
    S/N Ratio 35dB
    3DNR / WDR / OSD Yes / Yes / Yes
    Operating voltage 12VDC
    Current draw (IR on / off) 440mA / 80mA
    IP rating IP66
    Operating temperature -40°~131°F (-40°~55°C)
    Dimensions Ø3 15/16"x3 9/16" (Ø100x90mm) Ø5⅜"x5" (Ø136x127mm)
    Weight 16.72 oz (474g) 1 lb 9.3 oz (720g)

    OSD DIP Switch — Format Selection

    Move the two DIP switches inside the camera to select the analog format:

    Format DIP Switch 1 DIP Switch 2
    TVI (Default) OFF OFF
    AHD OFF ON
    CVBS (Analog) ON ON
    CVI ON OFF

    Before Starting

    • Use the camera within its rated temperature and voltage limits.
    • Do not point the camera at the sun — heat can damage it even when not in use.
    • Do not subject the camera to strong vibrations.
    • Do not mount in areas exposed to radiation, strong magnetic fields, or strong electrical signals.

    Installation Steps

    1. Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to the mounting location.
    2. Loosen the outer case ring and remove the case from the base. Note: the camera ball is not attached — it sits loose inside the case, so be careful not to drop it.
    3. Mount the base to the wall using the three included screws (use anchors for drywall, brick, or similar material).
    4. Run the camera's BNC and power connectors through the base and connect to the video/power wires run through the wall.
    5. Put the case over the camera ball and onto the base.
    6. Holding the case loosely, turn the camera ball to the desired direction. On the AMWWQ, use a small screwdriver through the marked "ZOOM"/"FOCUS" holes to adjust zoom and focus.
    7. Use the DIP switches to set the desired output format.
    8. Once positioned, tighten the outer case ring to secure the camera.
    9. Perform a final test of the camera and monitor, checking both day and night image quality.

    For the full On-Screen Display (OSD) manual, download it from the camera's product page at seco-larm.com.

    Important Notes

    • Do not cut the DC jack or BNC connector jack — doing so voids the warranty.
    • Do not open the camera case — there are no serviceable parts inside.

    Troubleshooting

    Symptom Checks
    Screen is black Check the camera is powered up; power supply polarity is correct; monitor is powered up; video cable is connected properly.
    Image foggy/washed out at night Check no objects are close to camera or highly reflective; clean lens with a soft cloth.
    Screen image is dim Check that the light source is adequate.
    Poor contrast Adjust monitor contrast; reposition the camera.
    Image flickers or is distorted Change camera position, check cables and the format DIP switch setting.
    Camera case is hot / IR LEDs won't turn on Check that the correct power supply is in use.

    Warranty

    SECO-LARM warrants this product against defects in material and workmanship in normal service for three (3) years from date of sale to the original customer. Obligation is limited to repair or replacement, transportation prepaid to SECO-LARM. Warranty is void for damage from acts of God, misuse, abuse, neglect, unauthorized repair/alteration, or faulty installation.