Menu
0
0

Your Cart is Empty

Add description, images, menus and links to your mega menu

A column with no settings can be used as a spacer

Link to your collections, sales and even external links

Add up to five columns

  • Add description, images, menus and links to your mega menu

  • A column with no settings can be used as a spacer

  • Link to your collections, sales and even external links

  • Add up to five columns

    • Home  / Product Manuals & Documentation
    Previous  / Next

    SECO-LARM ENFORCER SL-3301-BAQ Multi-Color LED Strobe Light — Manual

    September 08, 2026 2 min read

    Installation manual for the SECO-LARM ENFORCER SL-3301-BAQ multi-color LED strobe light with power-on and trigger modes.

    💾 Download Original PDF
    Full text manual (for reference)

    Installation manual for the SECO-LARM ENFORCER SL-3301-BAQ Multi-Color LED Strobe Light, with 7 selectable colors and dual power/trigger wiring modes.

    Features

    • 7 colors: red, green, blue, cyan, magenta, yellow, white
    • Operating life over 50,000 hours (5.7+ years) — no bulbs to replace
    • Simple 2- to 5-wire installation
    • Set color via DIP switches, or trigger colors externally via 3 trigger input wires
    • 5 vertical LED strips (25 LEDs total) for visibility from multiple directions
    • Adjustable strobe speed: 60–260 flashes/min
    • High-impact resistant case and heat-resistant lens; reverse polarity protected; weatherproof (IP66)

    Specifications

    Vertical LED strips / total LEDs 5 strips / 25 LEDs
    Operating voltage 9~24 VAC/VDC
    Current draw @12VDC 350mA (strobe or steady ON)
    Adjustable strobe speed 60–260 times/min
    Operating life 50,000+ hours (5.7+ years)
    Operating temperature -4°~144°F (-20°~65°C)
    Electrical protection Reverse polarity protected
    IP rating IP66
    Base / lens High-impact black ABS base; high-impact heat-resistant acrylic lens
    Dimensions 3-15/16" × 3-1/8" (100×79mm)

    Installation — Power ON Mode

    1. Mark the two mounting screw locations with a pencil.
    2. Drill through the mounting surface; run the ground (black) and power (brown) wires through. For surface wiring, remove the thinned-out slot with pliers.
    3. Connect the wires to the alarm/security panel.
    4. Remove the lens, mount the unit with the 2 included screws + rubber O-rings (don't over-tighten — damages the O-rings).
    5. Select color and strobe setting via the DIP switches, adjust speed with the strobe speed control (clockwise = faster).
    6. Replace the lens (don't over-tighten).

    Installation — Trigger Mode

    1. Same mounting steps as above, but run the ground (black) and 3 trigger wires (blue/green/red) instead of the power wire.
    2. Connect trigger wires to the alarm/security panel or trigger device per the color desired (see chart below).
    3. Mount the unit as above.
    4. Set the LED jumper to "strobe" or "steady ON" and adjust strobe speed.
    5. Replace the lens.

    Color / DIP Switch / Trigger Configuration

    Color Strobe DIP Steady-ON DIP Trigger Wire(s) to GND
    Red (default) R2 ON only R1 ON only Red
    Green G2 ON only G1 ON only Green
    Blue B2 ON only B1 ON only Blue
    Cyan G2 & B2 ON G2 & B2 ON Green + Blue
    Magenta R2 & B2 ON R2 & B2 ON Red + Blue
    Yellow R2 & G2 ON R2 & G2 ON Red + Green
    White R2, G2, B2 ON All ON Red + Green + Blue

    Note: In Trigger Mode, strobe/steady-ON behavior is set via the LED jumper (not DIP switches) — see the Overview diagram in the full manual.

    Troubleshooting

    Symptom Fix
    Strobe light doesn't turn on Check the power source
    Strobe light doesn't flash correctly Disconnect power, reconfigure color/strobe settings, reconnect

    Warranty

    One-year limited warranty against defects in material/workmanship under normal service.

    Manufacturer

    SECO-LARM U.S.A., Inc. — 16842 Millikan Avenue, Irvine, CA 92606. Phone: (949) 261-2999 / (800) 662-0800. www.seco-larm.com. Order Part# 762-514%