Luxul PDU-08 — Intelligent Network PDU Quick Install Guide

Quick install guide for the Luxul PDU-08 Intelligent Network PDU — a 9-outlet rack-mount power distribution unit with remote monitoring and control.

What's Included

• PDU 8 9-Outlet Intelligent Network PDU
• Ferrite RF Choke
• Power Cord

1. Physical Installation

The PDU 8 can be easily installed in a standard 19" rack. Two mounting ears are attached for securing the unit to rack rails. Install the device in the desired rack location and ensure it is secure.

2. Connecting Ethernet and Power

Connecting Power

Use the included power cable to connect the PDU 8 to an outlet with adequate current capacity. The AC input socket is on the rear panel. Once the power cable is connected, move the integrated retaining clamp into position to hold the power cable firmly and prevent accidental disconnection.

Note: The built-in power supply is compatible only with 120VAC at 60Hz. The PDU 8 is rated for 12A maximum continuous load and 15A maximum peak load — do not exceed these limits with the combined consumption of all powered devices. Use only the included power supply cord.

Connecting Ethernet

Connect the PDU 8 to your network with a standard Ethernet cable. Install the provided RF choke on the Ethernet cable as closely as possible to the connector going into the PDU 8.

Note: Luxul recommends at least Category 5 unshielded twisted pair (CAT5 UTP) cabling, but shielded cable (STP) is ideal for this application.

3. Access and Setup — Getting Connected

If the PDU 8 isn't already powered, power it on. The PDU 8 is configured to use DHCP. Once initialized, it will power on the switched outlets in sequence and obtain an IP address from a DHCP server on the network.

Using a computer or mobile device, log in to a router on the network and locate the PDU 8 in the router's DHCP client reservation table. Alternately, use a remote management system, IP scanner, or similar tool to find the PDU 8 and determine its IP address. The PDU 8 can be identified by its DHCP client name, which looks like "PDU-08-78083E" (the last half represents the last three octets of the device's MAC address). Make a note of the IP address. If the PDU 8 fails to find a DHCP server, it will default to IP address 192.168.0.6.

Logging In

To access the PDU 8 web UI, use a web browser on a computer or mobile device on the same network as the PDU 8. Enter the IP address in the address field, then log in using the default credentials:

• Username: admin
• Password: admin

Select the menu items to view and/or modify the configuration. For more guidance on setup and configuration, refer to the product support resources at luxul.com.

4. Hardware Operation

Front Panel

The front panel of the PDU 8 includes a powered unmanaged outlet, a status indicator, eight power status indicators for each of the controlled outlets, and a lighted power switch.

Rear Panel

The rear panel of the PDU 8 includes the power supply inlet (with cable retainer), 8 numbered controlled outlets, a reset button, an Ethernet port, and a grounding screw.

LED Indicators

LED indicators on the front panel show the operating status of the PDU 8 and each outlet — an overall device status LED, and a power status indicator for each of the eight controlled outlets.

Note: At startup, the outlet LEDs will power on in sequence.

Reset Button

The Reset button (lower-left corner of the rear panel) restores the PDU to factory default settings.

• To Reboot the PDU: switch the PDU 8 power off, wait a second, then switch power back on.
• To Restore Default Settings: with the PDU 8 powered on, press and hold the Reset button on the back panel for at least six seconds, then release. The PDU automatically restores factory default settings and reboots. Once the Status LED indicates normal operation, the PDU 8 is running again with factory defaults, including username/password and any IP configuration.

Note: Restoring Default Settings will remove any/all custom configuration.

Warranty & Support

This Luxul™ product has a 3-year limited product warranty and connected equipment protection policy. The warranty covers defects in workmanship and materials, provided the product remains unmodified and is operated under normal and proper conditions. Products returned to Luxul for warranty service must be accompanied by a Return Material Authorization (RMA) number.

Luxul offers free lifetime support of all products purchased through an authorized channel. Connected Equipment Protection Policy coverage is up to $25,000 — see the Luxul PDU warranty page for full details.

• Sales: 801-822-5450
• Technical Support: 801-822-5450 Option 3 / support@luxul.com

© Copyright 2017 Luxul. All rights reserved. Luxul, the Luxul logo, and Simply Connected are trademarks or registered trademarks of Luxul Wireless, Inc.