Legrand adorne ADTP700RMTU sofTap Dimmer — Installation Instructions

Installation instructions for the Legrand adorne™ ADTP700RMTU sofTap Dimmer, a 700W true universal whole-house wireless master dimmer.

Safety Warnings

• Shock hazard: to prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.
• Ground wire: failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.

Cautions

• To reduce the risk of overheating and possible damage to other equipment, do not install to control a receptacle, a fluorescent light or bulb, a motor-operated appliance, or a transformer-supplied appliance.
• Do NOT use this dimmer with incandescent lamps whose power requirements exceed the dimmer's maximum wattage.
• This dimmer does not have a minimum load rating.
• Do NOT connect the dimmer to a power source other than 120VAC, 60 Hz.

Installation Steps

1. Prep the frame: remove spacers from the frame — since this device fills the frame completely, spacers are not needed. From the back of the frame, pinch the tabs on the spacer to release it.
2. Cut wires: cut wires and strip insulation using the stripping guide on the back of the device. Use copper conductors only. When replacing an existing device, label wires before disconnecting, then disconnect the old device.
3. Multi-gang installations: use pliers to break off the specified heat sink fins as shown in the PDF diagram, then de-rate the maximum load per the table below.
4. Ground and mount the frame: connect the frame ground wire to the bare ground wire in the box. Fold ground wires into the back of the box. Mount the frame to the wall box with the screws provided — tighten just enough to hold the frame in place; do NOT over-tighten.
5. Wire the device: insert wires into terminals and tighten screws securely — do NOT over-tighten (torque to 10 in-lbs). For a single load: connect white wire to WHITE, black wire to HOT, red wire to LOAD. If installing multiple devices in one box, wire all devices before installing them into the box. Warning: do not pair different-size wires in the same terminal — use a wire nut to add a 6" pigtail of matching gauge to the smaller wire if needed.
6. Install into frame: carefully fold wires into the box, then snap the device(s) into the frame. To remove a device later, take the frame off the wall box, insert a flat screwdriver from the back of the frame, depress the tabs, and push the device forward.
7. Attach wall plate: snap the wall plate to the frame. There are three click-stops for alignment: first click = flush fit, second click = device protrudes slightly, third click = device protrudes fully. To remove the wall plate later, insert a flat screwdriver into the notches on the back of the plate and twist gently.
8. Notes: it is normal for the dimmer to feel warm during operation. Protect dimmers from dirt and dust.

Multi-Gang De-Rating Table

Wireless Pairing (House ID / Groups)

Set House ID — New Installation

1. Confirm all devices' status LEDs are solid AMBER.
2. Press and hold any dimmer/switch On/Off button (or Whisper Paddle top) for 5 seconds and release — the initiator's status LED flashes AMBER, and other devices' LEDs flash GREEN.
3. Press and hold the initiator's On/Off button for 5 seconds and release — both initiator and other devices flash GREEN for 2 seconds, then turn solid WHITE.

Adding a Device to an Existing Installation

1. Confirm the new device's LED is solid AMBER (others should be solid WHITE).
2. Press and hold any already-bound device's On/Off button for 5 seconds and release — initiator flashes AMBER, new device flashes GREEN.
3. Press and hold the initiator's On/Off button for 5 seconds and release — both flash GREEN for 2 seconds, then turn solid WHITE.

Creating a New Group

1. Confirm all potential group members' LEDs are solid WHITE.
2. Press and hold any device's On/Off button for 5 seconds and release (LED flashes AMBER); repeat for all potential group members.
3. Press and hold the initiator's button for 5 seconds and release — devices flash GREEN for 2 seconds, then turn solid WHITE.

Adding/Removing a Device from a Group

1. Confirm all potential group members' LEDs are WHITE.
2. Press and hold any existing group device's On/Off button for 5 seconds and release — current group members flash AMBER, non-group devices flash GREEN.
3. Press and hold the target device's button for 5 seconds — flashing AMBER joins the group, flashing GREEN leaves the group.
4. Press and hold the initiator's button for 5 seconds and release to finalize — LEDs flash GREEN for 2 seconds then turn solid WHITE.

Operation

Switch Mode

Press and release to toggle On/Off. Status LED is on when the load is off, and off when the load is on.

Dimmer Mode

• Press and release On/Off: toggles from off to last level, or on to off, at a 2-second ramp rate.
• Double-tap On/Off: full on at a 1-second ramp rate.
• Press and hold On/Off for 2 seconds: from off, no action; from on, ramps off slowly (30 seconds for 100%).
• Press and release Paddle (+): from off, ramps to last level over 2 seconds; from on, increases level 2% per tap.
• Double-tap Paddle (+): from off, ramps to full on over 1 second; from on, increases level 4%.
• Press and hold Paddle (+): increases level at a 5-second ramp rate.
• Press and release Paddle (−): from off, no action; from on, decreases level 2% per tap.
• Double-tap Paddle (−): from off, no action; from on, decreases level 4%.
• Press and hold Paddle (−): decreases level at a 5-second ramp rate.

Fault Indication

• Status LED blinking red 1x/second = no load
• Status LED blinking red 2x/second = over current
• Status LED blinking red 3x/second = short circuit

Factory Reset

Press and hold the On button for 20 seconds — status LED turns solid AMBER when the reset is complete.

Custom Setting Initiation (Dimmers)

1. Confirm all devices' status LEDs are solid WHITE.
2. Press and hold any dimmer's On button for 10 seconds and release — initiator's LED flashes GREEN, with blink count indicating the currently selected custom setting.
3. Press and release to cycle through custom setting selections.
4. Adjust the setting's level using the dimmer paddle press/release actions.
5. Press and hold the initiator's On button for >2 seconds and release to exit, or wait for a 60-second timeout.

Custom Setting List (by blink count)

Compatible Load Types

Incandescent/Halogen, Fluorescent, CFL, Magnetic Low Voltage (MLV — Forward Phase only), Electronic Low Voltage (ELV — Reverse Phase only), and LED.

Regulatory Compliance

FCC ID: YV8-202860. Complies with FCC Part 15 rules and Industry Canada RSS / ICES-003 standards. Changes or modifications not explicitly approved by Legrand could void the user's authority to operate this equipment.

Manufacturer

Legrand, 860.233.6251, www.legrand.us / www.legrand.ca. Doc #1507193.