Enbrighten 59337 (ZWA4011DV) — Z-Wave In-Wall Smart Switch Manual

Installation and setup manual for the Enbrighten Z-Wave In-Wall Smart Switch, Model 59337 (ZWA4011DV) — Z-Wave certified wireless lighting control.

Optional: Change the Paddle

Before installation, you may want to change the paddle to match your wallplate or décor.

1. Lift the air gap tab at the base of the paddle.
2. Push the side tabs in on one side, followed by the other, to release the paddle and lift it from the device.
3. Insert the air gap and side tabs, and snap the new paddle into place.

Remove Single-Pole Switch

1. Shut off power to the circuit at the circuit breaker or fuse box.
2. Important! Verify power to the switch box is OFF before continuing.
3. Remove the wallplate.
4. Remove the switch mounting screws.
5. Carefully remove the switch from the switch box — do NOT disconnect the wires.
6. Identify the following wires in the switch box: A. Ground – Green/bare, B. Line (hot) – Black (connected to power), C. Load – Black (connected to lighting), D. Neutral – White.
7. Disconnect the wires from the existing switch and label them according to their previous terminal connections.

Single-Switch Wiring

Wiring Requirements

Attach using the enclosure's holes; strip insulation 5/8 in. (16mm). UL specifies the tightening torque for the screws is 12 lbf-in (14 Kgf-cm).

Terminals: A. LINE — Black wire/black screw (input). B. LOAD — Black wire/black screw (output). C. GROUND — Green or bare wire/green screw. D. JUMPER — White wire/silver screw.

1. Connect the green/bare wire to the GROUND terminal.
2. Connect the black wire from the light to either LINE/LOAD terminal.
3. Connect the black wire from the power source (hot) to the other LINE/LOAD terminal.
4. Connect the white wire to the NEUTRAL terminal — use a jumper if necessary.
5. Secure the device into the switch box with the provided mounting screws — ensure wires are not pinched or crushed.
6. Install the wallplate.

Note: The traveler terminal is only used for multi-switch wiring and is not used in a two-way system (one switch and one load). Insert wires into holes — do NOT wrap wires around screws or remove screws.

Standard 3-Way Switch Wiring

Important! The Z-Wave device operates with add-on switches by default. To install with a standard 3-way switch, follow the "3-Way Configuration" steps below. The instructions here are for wiring a standard 3-way switch — see the add-on switch manual to install add-on switches.

Line Side (Z-Wave Device)

1. Shut off power to the circuit at the circuit breaker or fuse box.
2. Remove the line-side wallplate.
3. Remove the switch from the line-side switch box — do NOT disconnect wires.
4. Label the wire from the power source LINE.
5. Label one remaining wire "traveler 1" — note the wire color for installation of the 3-way switch.
6. Label the other remaining wire "traveler 2."
7. Disconnect all wires from the switch.
8. Connect green/bare wire to the GROUND terminal.
9. Connect the line wire to either LINE/LOAD terminal.
10. Connect the traveler 1 wire to the other LINE/LOAD terminal.
11. Connect the traveler 2 wire to the TRAVELER terminal.
12. Connect one end of a jumper to the bundle of neutral wires using a wire nut.
13. Connect the other end of the jumper to the NEUTRAL terminal.
14. Secure the device into the switch box with the provided mounting screws — ensure wires are not pinched or crushed.
15. Install the wallplate.

Load Side (3-Way Switch)

1. Remove the load-side wallplate.
2. Remove the switch from the load-side switch box — do NOT disconnect wires.
3. Label the wire from the light LOAD.
4. Label "traveler 1" wire — recall the wire color from the Z-Wave device installation.
5. Label "traveler 2" wire.
6. Disconnect all wires from the switch.
7. Connect green/bare wire to the GROUND terminal.
8. Connect the load wire to the traveler 1 wire using a wire nut.
9. Connect traveler 2 to the LINE (hot) terminal.
10. Connect one end of a jumper to the bundle of neutral wires using a wire nut.
11. Connect the other end of the jumper to the COMMON terminal.
12. Secure the 3-way switch into the switch box — ensure wires are not pinched or crushed.
13. Install the wallplate.
14. Apply power to the fuse box or breaker.

3-Way Configuration

The smart device is set to work with add-on switches by default. To use with a standard 3-way switch:

1. Pull out the air gap switch.
2. While pressing the top paddle, push in the air gap switch.
3. Continue pressing the top paddle until the LED flashes yellow three times, indicating standard 3-way switch configuration.
4. Repeat these steps to return to the add-on switch setting — LED flashes blue three times.

Add-On Switch Compatible

Enbrighten, UltraPro, and JascoPro Series add-on switches support the same features as the Z-Wave device — single-, double-, and triple-tap functions — from all locations. Supports operation from up to five locations with a uniform appearance. Visit byjasco.com to purchase add-on switches.

Cycle LED (Guide Light / Status Indicator)

The LED below the switch acts as a guide light or status indicator.

1. Press the menu button for five seconds.
2. Press up three times and down one time quickly — indicator flashes blue.
3. Push the top paddle: once for LED ON when load is OFF (illuminates orange to confirm); twice for LED ON when load is ON (illuminates yellow to confirm); three times for always OFF (illuminates pink to confirm); four times for always ON (illuminates purple to confirm).
4. Press the menu button once to save — indicator flashes green twice.

Change LED Indicator Color

1. Press the menu button for five seconds.
2. Press top paddle once and bottom paddle once — LED illuminates in the selected color.
3. Press top or bottom paddle to cycle through color options: Red, Orange, Yellow, Green, Blue (default), Pink, Purple, White.
4. Press the menu button once to save — indicator flashes green twice.

Adding Your Device to a Z-Wave Network

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the top or bottom of the rocker.

You have complete control to turn your fixture ON/OFF according to groups, scenes, schedules, and interactive automations programmed by your controller. If your controller features remote access, you can control your fixture from mobile devices. If prompted for the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product, and enter the 5-digit PIN.

Note: SmartStart-enabled products can be added to a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion — no further action is required, and the product will be added automatically within 10 minutes of being switched on in the network vicinity.

To Remove and Reset the Device

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press the top or bottom of the rocker.

Return Your Switch to Factory Defaults

1. Pull up the air gap switch.
2. While pressing the OFF (bottom) button, push in the air gap and continue pressing the OFF button. The LED flashes through the eight colors once.

Note: This should only be used if your network's primary controller is missing or otherwise inoperable.

Features

Important! The fixture controlled by the Z-Wave in-wall smart switch must not exceed switch ratings. The switch is designed only for use with permanently installed fixtures.

• Turn ON/OFF manually or remotely through the Z-Wave controller
• Can be added in multiple groups and scenes
• Auto-detect line/load terminals
• May be used in single-pole installation or 3-way wiring configurations
• Compatible with all LED, CFL, incandescent, and halogen lights
• Interchangeable paddle
• Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
• Multicolor LED indicates switch location in a dark room
• Screw terminal installation — requires wiring connections for line (hot), load, neutral, and ground. Traveler wire required for 3-way installation.
• Advanced configuration features adjustable only via a Z-Wave enabled controller supporting the Z-Wave configuration command class. Full list at www.ezzwave.com/config

Z-Wave Interoperability

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or applications. All non-battery operated nodes within the network act as repeaters regardless of vendor, to increase network reliability. This device supports the association command class (3 groups):

• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set, controlled by pressing the ON or OFF button with the local load
• Association Group 3 supports Basic Set, controlled by double-pressing the ON or OFF button
• Each Association Group supports 5 total nodes

Specifications — ZWA4011DV

Important Safety Notices

• Risk of fire, electrical shock, and burns.
• This switch is rated for and intended to only be used with copper wire.
• Use 14AWG or larger wires suitable for at least 90°C for supplying line (hot), load, neutral, ground, and traveler connections.
• Do not exceed ratings.
• Do not use to control any device where unintended operation could cause unsafe conditions (heat lamp, sun lamp, etc.)
• Not for use with medical or life-support equipment.
• For indoor use only.

FCC / IC Notice

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. See product label for FCC/IC certification numbers. CAN ICES-3(B)/NMB-3(B).

Warranty

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to repair or replacement of the product only and does not extend to consequential or incidental damage to other products used with it. Some states do not allow limitations on implied warranty duration or exclusion of incidental/consequential damages, so the above limitations may not apply to you.

Questions? Contact U.S.-based Consumer Care at 1-800-654-8483, 7AM–8PM, M-F, Central Time, or visit www.byjasco.com. Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114. Made in Malaysia. © JASCO 2022 | ZWA4011 | 59337