Chief Thinstall LTTU Large Tilt Universal Mount — Installation Manual

Overview

Installation instructions for the Chief® Thinstall™ LTTU — a Large Tilt Universal Mount for flat panel displays. The LTTU fits all VESA hole patterns between 200×200 mm and 800×500 mm, supports display depths up to 2 inches (50.8 mm), and offers up to 12° of forward tilt.

Important Warnings

• Structural strength: the wall structure must support 5 times the combined weight of all mounted equipment; reinforce as needed.
• Weight limit: combined weight of all components from the LTTU up to and including the display must not exceed 100 lbs (45.4 kg).
• Displays can weigh over 40 lbs (18.1 kg) — always use two people and proper lifting technique.
• Improper installation can cause the mount to fall, causing severe injury or equipment damage.

Wall Plate Installation

Using Wood Studs

1. Determine mount location, factoring in display size and safety requirements.
2. Use a stud finder to locate studs. The wall plate mounts on studs spaced 16", 20", or 24" apart for double-stud mounting; for triple-stud mounting, studs must be 16" apart.
3. Using the wall plate as a template, mark and drill four (double-stud) or six (triple-stud) 3/16" diameter pilot holes centered in each stud, at least 2-1/4" deep.
4. Install connector screws through the wall plate into the pilot holes using the included M4 Allen head bit.

Into Concrete, Concrete Block, or Brick

1. Determine mount location.
2. Using the wall plate as a template, mark and drill six 5/16" diameter pilot holes at least 2-1/4" deep. Use a level to ensure the wall plate is perfectly horizontal.
3. Install six anchors into the pilot holes, lightly tapping with a hammer.
4. Install six connector screws through the wall plate holes and into the anchors.

Display Installation

1. Lay the display face-down on a level, non-abrasive surface (use a cloth to avoid scratching).
2. Position the left and right interface brackets over the mounting holes on the back of the display; the diamond hole in each bracket should sit halfway between the installation holes for proper weight distribution. Brackets may need to be expanded to the tilt position to expose the installation holes.
3. Choose the correct screws that fit the display's mounting holes — screws should make at least three full turns; select a longer screw if needed.
4. Select the correct washers and spacers per the screw size (see table below).
5. Install four button head cap screws through the required washers, spacers, and interface brackets into the back of the display.
6. While supporting both sides of the display, lift it up to the wall plate.
7. Guide the hooks on top of the interface brackets onto the wall plate at the desired mounting location.
8. Slowly swing the display toward the wall.
9. Rotate the flags on each interface bracket down to the closed position to lock the brackets to the wall plate.

Screw/Washer/Spacer Reference

Tilt Adjustment

• Tilt the display forward by pulling on the top edge as desired.
• Tilt tension is adjustable with a 3/16" hex key on the tension adjustment nut. Adjust tension equally on each bracket for even distribution.

Note: due to the low profile of the Thinstall series, certain displays may have limited tilt capability.

Cable Management

The LTTU features a kickstand for easy cable access without removing the display from the wall.

1. Ensure the mount and display are in the upright position.
2. Slowly pull the bottom of the display away from the wall until the kickstand fully reaches its down position.
3. Release the display until the kickstand locks against the wall.
4. Attach or adjust cables on the back of the display.
5. To disengage the kickstand, slightly pull the display away from the wall, pull down on the cable management straps to release, then slowly allow the display to return to the wall.

Note: due to the low-profile design of the Thinstall series, displays with cable connections coming straight out of the back may require 90-degree cable connectors. Chief offers in-wall accessories that can help recess cables and connections.

Manufacturer

Chief Manufacturing, a products division of Milestone AV Technologies — 8401 Eagle Creek Parkway, Savage, MN 55378. Phone 800.582.6480 / 952.894.6280. www.chiefmfg.com. Chief® and Thinstall™ are registered trademarks of Milestone AV Technologies.