GE Security PrecisionLine RCR-PET Dual Technology Motion Sensor — Installation Instructions

Installation Instructions for the GE Security PrecisionLine RCR-PET Dual Technology Motion Sensor — a pet-immune (up to 80 lbs.) combination range-controlled radar (RCR) and passive infrared (PIR) motion detector for use with UL-listed security control panels.

Description

The PrecisionLine RCR-PET combines radar (RCR) technology with a PIR system to increase false-alarm immunity by sensing human-sized objects within a specified range. Both the RCR and PIR systems must be triggered together to set off an alarm. The sensor runs on a 12VDC power supply provided by a UL-listed control panel.

Features

• Pet immune up to 80 lbs.
• Selectable range up to 35 feet (10.7m) via an internal jumper to optimize coverage
• Multi-color LED indicator showing detector status
• Opaque Fresnel lens that blocks visible light

Parts Included

• RCR-PET sensor
• 1 screw to join the case halves
• 2 factory-installed jumpers

Coverage Pattern

The sensor covers a 90° radius, with radar/PIR range settings selectable at 9', 18', 27', or 35 feet (2.7m / 5.5m / 8.2m / 10.7m) from the sensor, both in top-down and side-view coverage patterns. Side-view coverage extends down to floor level at increasing distance from the mount, tapering off around 4° elevation at the maximum 35' range.

Selecting a Location

• Mount so expected intruder movement falls within a 90° radius in front of the sensor.
• Mount on a stable surface 7 to 8 feet (2.1 to 2.4m) high.
• Do NOT mount within 2 feet (0.6m) of metallic objects.
• Do NOT place objects in front of the sensor that block a clear line of sight.
• Avoid exposure to false-alarm sources: moving/vibrating objects (fans, pulleys, conveyor belts); electronic fields (motors, high-voltage equipment); water spray or corrosive environments; heat sources (heaters, radiators) in the field of view; windows in the field of view; strong air drafts (fans, A/C).
• When installing multiple sensors: do NOT mount sensors facing each other; mount at least 20 feet (6.1m) apart. Back-to-back mounting is not recommended, but if required, use the 9-foot range, mount at least 1 foot (0.3m) apart, and walk-test the installation.

Installing the Sensor

All wiring must conform to the National Electric Code (NEC) and/or applicable local codes.

Important: Do NOT use this device for safety interlock applications.

1. Run security system wiring to the sensor location.
2. Lift off the front cover/electronic module; remove the nameplate and loosen the screw if necessary.
3. Caution: Discharge all static electricity before handling the circuit board — touch a grounded, bare metal surface or wear a grounding strap first.
4. Set the circuit board jumpers as needed (see Setting the Jumpers below).
5. Remove the appropriate wiring/mounting knockouts from the back cover — the sensor can be mounted on a flat wall or in a corner.
6. Pull the wires through the knockout holes and attach the base to the wall with the two provided screws (use anchors if necessary).
7. Strip 1/4 inch (6.4mm) of insulation from each wire.
8. Run each wire through the strain relief and under the appropriate screw terminals on the base; tighten the screws.
9. Align the tabs on the bottom of the cover/electronic module with the base and snap the module firmly onto the base.
10. Tighten the screw and replace the nameplate.
11. Apply power — the LED lights green for about 25 seconds, then goes out.
12. Walk-test the coverage pattern by walking through the intended coverage area and verifying the sensor alarms (see Understanding the LED below).

Setting the Jumpers

J2 — Range Selection

Use the jumper to cover the center pin and the pin for the desired range:

• No jumper = 27 feet (8.2m) and under
• 35 feet (10.7m) and under — factory default
• 18 feet (5.5m) and under
• 9 feet (2.7m) and under

Important: Set J2 as close to the intended coverage range as possible — overshooting the coverage area may cause false alarms.

J3 — LED

• ON = LED enabled (factory default)
• OFF = LED disabled

Pet Immunity

When mounted properly, the RCR-PET provides false-alarm immunity to dogs and similar animals. Immunity depends on the animal's size, temperature, and coat length — a warm-blooded, short-haired dog is less immune to false alarms than a similarly-sized dog with a longer coat, so short-haired dogs must be smaller/lighter to remain covered.

Pet immunity is not verified by UL.

Understanding the LED

After 30 minutes, the LED only indicates an alarm condition. Drop power to reset the walk-test timer.

Accessories

SB01 Swivel-Mount Bracket — an optional ceiling-mount swivel bracket for ceiling-mount applications requiring 90° coverage.

Maintaining the Sensor

When installed and used properly, the sensor provides years of service with minimal maintenance. Walk-test the sensor annually to ensure proper operation.

Specifications

Product Ordering

FCC Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: CGGAA2

Contact

GE Security, 12345 SW Leveton Drive, Tualatin, OR 97062 — 503-692-4052, USA & Canada: 800-547-2556

Tech Support: 800-648-7424, FaxBack: 800-483-2495, www.ge-security.com