• Home
  • Seco-Larm Enforcer Long Range Barrier Sensor, 190'

Seco-Larm Enforcer Long Range Barrier Sensor, 190'

SKU: SEE96798B190Q

Usually ships in 3-5 days.

NOTE: This is a heavy/dimensional part; it is not eligible for free shipping.


WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov


Set Up Complete Long-Range Perimeter Security

The Seco-Larm Enforcer Long Range Barrier Sensor, Indoor/Outdoor, 190ft provides an easy way to implement long-range perimeter security for any area on your property. This sensor includes a transmitter and receiver that will trigger when there's either a simultaneous breaking of beams or after a single pair of beams is broken for at least 2 seconds. Using reliable photobeam technology, this sensor provides four programmable beam frequencies to eliminate crosstalk and interference when multiple units are used. It also allows you to program the alarm output trigger operation to reduce false alarms caused by falling leaves, animals, bad weather and other sources.

  • Indoor/outdoor perimeter security with long sensing range (190ft outdoors, 380ft indoors)
  • Install over windows, doorways, skylights, fence tops, etc.
  • Triggers on simultaneous breaking of beams, or after a single pair of beams is broken for 2 seconds (programmable)
  • Tamper switches built-in on either end trigger the alarm if the end cap is removed
  • LED alignment indicator simplifies installation
  • Rugged, weatherproof aluminum construction

The Seco-Larm Enforcer Long Range Barrier Sensor also features a built-in heater that turns on and off depending on the outdoor temperature, and has an environmental control system to sense the slow degradation of the beam strength if weather conditions worsen. The sensor is perfect for installation on windows, doorways, skylights, fence tops, garages, and more.


  • End caps swivel so sensor can be mounted on a single wall or on opposite walls with no L-bracket needed
  • Heater for use in cold weather operation, activates at 41°F (5°C)
  • Terminal block wiring
  • Slim design: 2-1/4" x 1-7/8" (55 x 49 mm)
  • No synchronizing wires required to align the beams
  • Form C relay output
  • LED and buzzer alignment indicators
  • AGC (Auto Gain Control) circuits regulate beam signals in order to compensate for and ensure operation in rain, fog, and low temperature conditions


  • Transmitter
  • Receiver
  • Manual
  • (4) Pole Mount Brackets
  • (8) Machine Screws 4x6mm (for pole mount brackets)
  • (8) Machine Screws 4x25mm (for pole mount brackets)
  • (12) Screws 6x20mm (for wall mount use)
  • (12) Plastic Anchors (for wall mount use)

Seco-Larm Security Products

So many places and things to protect; so many ways to protect them; one partner: Seco-Larm. Under the Enforcer trademark, Home Controls offers an impressive line of Seco-Larm security products, ranging from simple switches to some of the most sophisticated alarm devices. Whether for physical security, CCTV, access control, RF equipment, or vehicle security, Seco-Larm is the premier choice. Seco-Larm gives its customers such an extensive range of dependable, cost-effective security products with a full program of service and support.


  • Manufacturer Part #: E-9679-8B190Q
  • Number of Beams: 8 pairs
  • Max. Range (outdoor): 190 feet (60m)
  • Max. Range (indoor): 380 feet (120m)
  • Heater Active Current (Rx+Tx): 160mA@12VDC
  • Current Draw: 20~160 mA@12VDC
  • Input Voltage: 12~24 VDC
  • Response Time (receiver): 150/300/450/600 ms (DIP switch programmable)
  • Alarm Output: NO/NC/COM, relay output, if triggered, active for 1 sec.
  • Tamper Output (Tx & Rx): 1A@120VAC/1A@24VDC
  • Operating Temperature: -49°F to 131°F (-45°C to 55°C)
  • IP Rating: IP65
  • Length: 79 inches (201cm)
  • Width and Depth: 2-1/4 x 1-7/8 inches (55x49 mm)
  • Credentials: CE, RoFC
  • Warranty: 1 Year