• Home
  • FortrezZ Z-Wave MiMO2+ Interface Module

FortrezZ Z-Wave MiMO2+ Interface Module

Order now and we'll ship same business day (if ordered before 3 pm PST).


WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Make Any Two Devices Speak Z-Wave

Turn almost any device into a Z-Wave enabled device by connecting it to the FortrezZ Z-Wave MIMO2 Interface Module. This 2-input, 2-output (IO) module is perfect for controlling anything from a garage door to a drapery motor. You could even use it as a doorbell sensor to receive Z-Wave alerts when a visitor rings your traditional mechanical doorbell. And because the 4 inputs and outputs can be used simultaneously, you could optionally activate an output whenever the input is triggered!

  • Provides 2 input and 2 relay output (NO/NC)
  • Converts wired devices into Z-Wave capable wireless devices
  • Works with SmartThings and Zipato Controllers
  • System includes program switch and LEDs for status indications.
  • Supports latching or momentary functionality

How It Works

The MIMO2 is capable of converting a digital or analog voltage input and/or a Z-Wave RF message input into a dry contact relay output and/or a Z-Wave RF message output, making it incredibly flexible for a wide variety of applications. It has an input for digital or analog devices operating at 0 to 16VDC (or up to 16Hz for pulse counting), and it has a true 12V-24V dry voltage relay output (normally open/normally closed) with a maximum switching power of 120W.

The module supports either latching or momentary/pulsing applications. When used as a momentary relay, you can adjust the timing from 32 milliseconds (default) up to 3 seconds.

Possible Applications:

  • Garage Door Opener
  • Doorbell Sensor
  • Gas Fireplace
  • Wired Lighting
  • Drapery Motor
  • Electric Door Strike
  • Motorized Water Valve

Switching Between Latching vs. Momentary

If you want to switch from latching to momentary, or vice versa, but you have already enrolled the module into your Z-Wave controller, you need to first un-enroll the module from your controller, then enroll it again in order to switch to your desired function.


  • MIMO2
  • Power Adapter, 9V
  • User Manual


  • Requires a Z-Wave network controller (sold separately).
  • Not rated for outdoor use.
  • Do not attempt to use the relays to switch residential or industrial Alternating Current (AC) lines. The relays are to be used for low-power load control only. The MIMO2 must not be used in life support and/or safety applications.

Reinforce Your Home With FortrezZ

With more than 20 years of experience in developing RF wireless technologies, FortrezZ LLC is now a leading design and manufacturing company for high-grade automation and security products. FortrezZ is committed to excellence in every aspect, from product construction to customer satisfaction, and has become a valued member of the reputable Z-Wave Alliance. Feel confident in your installations with FortrezZ products.

  • Manufacturer Part #: FZMIMO2US
  • Power: 12-16 VDC from a power supply at ~500mA capability
  • Frequency: 908.4MHz (U.S.) Z-Wave; 868.4MHz (EU)
  • Wireless Range: Max 100 feet line of sight in unobstructed environment
  • Input Signal 1,2 (SIG1 & SIG2): Digital or Analog Input 0 to 16VDC or 16 Hz Max for pulse counting. The trigger levels and hysteresis can be set via the Configuration Command Class for each endpoints.
  • Input Signal Impedance: For SIG1: Z=66 ohms at 10KHz. This impedance is = 66 ohm = 34 ohm + j 540uH.
  • Output Relay 1,2 (REL1 & REL2): SPDT, Max. Switching power of 120W; 10uA to 10A; High Dielectric strength coil-contacts: 1,000VAC.
  • Open Contacts: 750VAC; Conforms to FCC Part 68 requirements; Ag + Au clad bifurcated contacts fully sealed.
  • System Requirement: Any Z-Wave enabled network and controller
  • Operating Temperature: 14° to 158°F (-10° to 70°C)
  • Enclosure Size: 3-3/8(L) x 2-1/2(W) x 1-1/4(D) inches (85 x 64 x 30mm)
  • Weight: 4 ounces (100 g)
  • Warranty: 1 Year