WIRELESS RF CONTROL OF UPB SWITCHES

RF Control of UPB Switches The project will enable you to have wireless RF control of your UPB switches. The keyfob remote will have the ability to turn ON/OFF/Dim/Bright a switch or a group of switches. The SSWA6R Wireless Automator is a pre-programmed kit with an RF receiver containing 6 relay outputs, 4 button keyfob and plug-in power supply. All relay outputs are defaulted to “validity” mode, i.e. the relay is activated until the transmitter button is released. The buttons are pre-configured as follows: Transmitter button I = Relay 1 Transmitter button II = Relay 2 Transmitter button III = Relay 3 Transmitter button IV = Relay 4 Transmitter buttons I & II Simultaneously = Relay 5 Transmitter buttons III & IV Simultaneously = Relay 6 The SAUMI32W Input Output module is a plug-in module designed to transmit the status of low voltage inputs or contact closures, and to control the operation of low voltage actuators based on digital commands received over the powerline. It is useful for detecting events such as ringing phones or doorbell or siren, for monitoring alarm switches on doors and windows or sensing audio signals from a sound system.

WHAT YOU NEED:
Street Smart Wireless Automator Kit SKU: SSWA6R Order Now >>	SAI Computer Interface Module SKU: SAUMCDB9W Order Now >>
SAI Input/Output module SKU: SAUMI32W Order Now >>	Gel filled “B” Connectors, 50 Pack SKU: ELK9022 Order Now >>
SAI Transceiver Switch (programmed via UPStart software) SKU: SAUS1130W Order Now >>	Downloadable UPStart Software, Free Download Now

HOW TO INSTALL IT:

Input/Output Module (SAUMI32W)

1. The SAUMI32W Input/Output UPB module is a plug-in device that can be programmed to control UPB devices and other low voltage devices directly from its relay outputs. Initial unit address programming is done through the UPStart software and SAUMCDB9W computer interface module (CIM).
2. Connect the CIM to an available PC serial port and open UPStart software.
3. From the Upstart Menu, click Device, Add. Choose MFR: Simply Automated, Product: UMI-32 3 Input 2 Output Module but do not click Next yet.
4. Plug the SAUMI32W into a 110VAC outlet and place in programming mode by tapping program button 5 times. The Program LED’s will start to blink green. Click Next. Assign SAUMI32W to the first available UPB unit ID (Default Unit ID is 40).
5. Program Link xxx into Input 1 to trigger the UPB switch or switches. ( Open event = Deactivate, Close event = Activate)
6. Program Link xxx (same as above) into Input 2 to trigger Bright Commands (Open event = Fade stop, Close event = Fade up)
7. Program Link xxx (same as above) into Input 3 to trigger Dim Commands (Open event = Fade stop, Close event = Fade down)

Wireless Automator Installation (SSWA6R)

1. Mount SSWA6R in a suitable location.
2. Connect enclosed wire harness to SSWA6R and strip ¼’’ insulation from the following wire colors : Red, Black, Purple, Purple w/ black stripe, Orange, Orange w/ black stripe, Blue, Blue w/ black stripe
3. Insert the following wires to SAUMI32 input connections:
   
   Black = input 6
   Purple = input 7
   Orange = input 9
   Orange w/ black stripe = input 10
   Blue = input 15
   Blue w/ black stripe = input 16
   
4. Twist Red and Purple w/ black stripe wires together and crimp with B connector.
5. Power up SSWA6R with included power supply.
6. Configure relay 1 output for Latching/toggle mode. Refer to SSWA6R installation manual for programming.

SAI Transceiver Switch Installation

1. Shut off circuit breaker powering the switch that will be replaced.
2. Replace the appropriate switch with the SAI Transceiver switch. Refer to the mfr’s instructions for installation details.
3. Power up the circuit breaker and test the Transceiver Switch manually for correct operation.
4. Program via UPStart to respond to links programmed in the I/O Module. See step 2 of the Input/Output Module above.
5. From the UPStart menu , click Device, Add. Choose MFR: Simply Automated and Product: US1/US2 Dimming Switch. Do not click NEXT yet.
6. Place Dimming Switch in Program mode by tapping rocker 5 times. LED starts to blink green. Click Next.
7. Program switch to respond to Link xxx programmed in I/O Module.
   

SUMMARY
The SSWA6R outputs allow the I/O module to generate the necessary UPB ON/OFF/Dim and bright commands. Relay 1’s toggle configuration enables the keyfob to turn ON (initial Button 1 push) and OFF (next Button 1 push). Relays 2 and 4 “validity” modes create the perfect trigger for a UPB dim or bright command. Recommend labeling Button I for Power, Button II for Bright and Button IV for Dim.